geographic.org Opening: Building Your Own Texas Flood Pedal So, you're chasing that iconic Stevie Ray Vaughan tone? The "Texas Flood" solo is drenched in bluesy overdrive. While there are many pedals that try to capture that sound, building your own can be a rewarding (and potentially cheaper) experience. This guide will walk you through the steps of creating a modified Tube Screamer-style overdrive pedal tailored to nail that Texas Flood vibe.
Step 1: Gathering Your Components You'll need to acquire a variety of electronic components. A comprehensive parts list is crucial. Here's a suggested list, but feel free to adjust based on your preferred suppliers and desired modifications:
- 1 x PCB (Printed Circuit Board) for a Tube Screamer clone (many available online)
- Resistors: assorted values including 100Ω, 220Ω, 470Ω, 1kΩ, 2.2kΩ, 4.7kΩ, 5.1kΩ, 10kΩ, 22kΩ, 47kΩ, 51kΩ, 100kΩ, 220kΩ, 470kΩ, 510kΩ, 1MΩ
- Capacitors: assorted values including 1nF, 4.7nF, 10nF, 22nF, 47nF, 100nF (0.1uF), 1uF, 4.7uF, 10uF, 22uF electrolytic
- Diodes: 1N4148 (x2), optional: different clipping diodes for experimentation (e.g., germanium, LEDs)
- Op-amp: TL072 or JRC4558D (the latter being a popular choice for Tube Screamer clones)
- Potentiometers: 100kΩ (Drive), 500kΩ or 1MΩ (Tone), 100kΩ (Volume) these can be linear or audio taper based on preference
- 3PDT Footswitch (for true bypass)
- 9V Battery Clip or DC Jack
- Enclosure (e.g., 1590B)
- Knobs for Potentiometers
- Wire (solid core or stranded)
- Solder
- Soldering Iron and Solder Sucker/Desoldering Braid
- Wire Strippers
- Multimeter
- Drill and Drill Bits (for enclosure)
Step 2: Preparing the PCB Carefully inspect your PCB. Most clone boards will have component placement guides printed on them. Begin by soldering in the resistors. Bend the resistor leads, insert them through the appropriate holes on the PCB, and solder them in place. Clip off any excess lead length. Repeat this process for the diodes, ensuring correct polarity. Usually, a stripe on the diode indicates the cathode. Then solder the IC socket where the Op-amp will eventually go. This protects the Op-amp from heat during soldering. Next, proceed with soldering the capacitors. Pay attention to the polarity of electrolytic capacitors; usually, a stripe indicates the negative lead.
Step 3: Wiring the Potentiometers and Footswitch The potentiometers (Drive, Tone, Volume) need to be wired to the PCB. Refer to the schematic for your specific Tube Screamer clone for the correct connections. Typically, the outside lugs of each potentiometer are connected to ground and a signal path on the PCB, while the center lug becomes the adjustable output. The 3PDT footswitch is used for true bypass. Wire it according to a standard 3PDT wiring diagram available online. This will switch between the effect being engaged and a direct, unaltered signal.
Step 4: Modifying for "Texas Flood" Tone (Optional, but Recommended) While a standard Tube Screamer clone will get you in the ballpark, certain modifications can help you get closer to the SRV tone:
- Reduce Gain: Lower the value of the feedback resistor (typically around 510kΩ) in the op-amp's feedback loop. Try values from 470kΩ down to 330kΩ. This will reduce the overall gain and make the pedal more responsive to your guitar's volume knob.
- Asymmetrical Clipping: Experiment with different clipping diodes. Instead of two identical 1N4148 diodes, try using one 1N4148 and a germanium diode. This will create asymmetrical clipping, which many believe contributes to the SRV sound.
- Boosted Mids (Carefully): While the Tube Screamer is known for its mid-hump, SRV's tone wasn't overly nasal. Experiment with slightly altering the tone control's capacitor values, but be subtle. Small changes can make a big difference.
Step 5: Assembling and Testing Mount the PCB, potentiometers, and footswitch inside the enclosure. Ensure all components are securely fastened. Connect the 9V battery clip or DC jack to the appropriate points on the PCB. Before fully closing the enclosure, thoroughly test the pedal. Plug in your guitar and amplifier and check that the effect engages and disengages properly, and that the Drive, Tone, and Volume controls function as expected. Use a multimeter to check for any shorts or voltage issues.
Step 6: Final Touches If everything is working correctly, carefully close the enclosure. Attach the knobs to the potentiometers. You can add labels to the enclosure indicating the function of each control.
Conclusion Building your own "Texas Flood" pedal is a challenging but highly rewarding project. Experiment with the modifications to find the tone that works best for you and your gear. Remember to prioritize safety when working with electronics. With patience and attention to detail, you can create a pedal that captures the essence of Stevie Ray Vaughan's legendary sound.
Maps Of Texas
geographic.org Texas State Map
ontheworldmap.com Map Of Texas
www.turkey-visit.com
0 komentar:
Posting Komentar